How to Remove Stuck Bike Pedals

Stuck bike pedal can be disappointing especially since they deny you the fun you intend to enjoy with your bike. But such a situation is only temporary and fixable within a couple of minutes if you have the idea on how to remove stuck pedals on a bike.

There are a few reasons as to why a bike pedal might get stuck. It could be that is has been tightened way too much or maybe due to rust from old age. All in all, learning how to remove stuck bike pedals is an easy task, and with this review, you should be well informed on how it is done by the end.

What You Will Need: To Remove Stuck Bike Pedals

To remove your bike pedals on your own at home, the following should be available or effortlessly accessible to make it a smooth DIY project without any stress or fuss:

  • A large open space to work easily and move around without any obstacles
  • Old clothes or shop towels for messy situations and drying
  • Long-handled Allen key wrench
  • Pedal wrench
  • Lubricating bike pedal spray
  • Cleaning solution
  • Spare screws that fit the size of your pedal just in case they are required

Any of the above supplies, tools, or equipment should be available at your nearby hardware store or a bicycle repair shop if you don’t have them in your garage or bike tool kit.

How to remove stuck bike pedals step by step

Step one: Protect your knuckles

Start by moving your chain onto the big ring, this means that any slips are less likely to result in a chainring-related knuckle injury. This is one of those rare jobs that are simple to carry out with the bike resting the right way up on the ground rather than suspended in mid-air in a bike stand.

Step two: To the left

Starting on the drive side, put the crank into the 3 o’clock position, so it points forward, parallel to the ground. Most pedals will take an Allen key in the back. Insert this so it sits below the level of the crank. Now push down and forwards, turning anticlockwise. You can use proper force.

Step three: To the right

Swap to the opposite side and place the crank in the 9 o’clock position. Repeat the procedure as before, pushing the Allen key down and forwards. This time the pedal will turn clockwise. Next, turn the pedal off. Make sure to keep any washers that fall out as you’ll need them when fitting your new pedals.

Step four: Clean up and inspect

Give the threads on the axle and inside the end of the crank a quick wipe down and check for any indication of damage. If they look worn, your nearby bike shop can save the day by using a tapping tool. This only tends to be something to worry about if the pedals have been difficult to remove.

Step five: Squeeze of grease

If you’re happy with the condition of your axle threads, add a quick squeeze of grease or anti-seize. This won’t just decrease the possibility of them squeaking as you pedal, but should ensure that the next time you come to remove them they’ll come undone without too much of a struggle.

Step six: Spinback on

Find the markings on the pedals to distinguish between left and right. Replace any washers and gently thread the pedals back onto the crank as any force can cause damage. Each pedal will tighten by turning towards the front of the bike. The right pedal goes on clockwise and the left, anticlockwise.

Warnings

  • Don’t use heat to unscrew the nuts. This is a method used only by professionals since it needs passing an open flame through the pedals. The chances are that you will end up harming your bike.
  • While unscrewing the nut holding in the pedal, don’t apply too much force on it.
  • Take caution not to harm any other parts of the bike as you forcefully try to loosen the pedal.

Tips

  • There are special lubricants that are designed for unscrewing nuts. These are the best to use in coaxing the but fixing the pedal in place to loosen.
  • If you use heat, it would be best if you used a hairdryer instead of flames.
  • Be careful while unscrewing the nuts as your bike rests against the wall. You could end up grazing the other pedal.
  • Always clean your pedals and oil them to keep them in great condition.

Conclusion

We have just discussed not only how to remove stuck bike pedals but also how to do it yourself without having to bring your bike to an expensive service shop. With a little bit of effort and time, you can easily remove your bike pedals at home for a cleanup job or total replacement. Once those bike pedals are cleaned and then you are ready to ride.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: